Need Garage Door Service Aledo?

Call to Schedule your FREE Estimate!

817-681-8186

Repair and Garage Door Service Aledo

• Overhead Door Repairs
• Garage Door Roller Replacement
• Garage Door Spring Replacement
• Garage Door Tune Ups and Maintenance
• Garage Door Opener Repairs

New Garage/Overhead Doors

• Custom Garage Doors
• Designer Garage Doors
• Traditional Garage Doors
• Commercial Overhead Doors
• Overhead Door Openers

Garage Door Inspection

DAPco Garage Door Service Aledo offers a 25 Point Inspection to residential homes across the DFW Metroplex. With our $45.00(free with other repairs/replacements) 25 Point Inspection lube and tune service executed by our experienced technicians, your garage door systems is fully evaluated. Each component of your garage door is lubed and tuned accordingly to keep your garage door running smoothly and efficiently.

Garage Door Lubrication

DAPco Garage Door Service Aledo/a> not only performs all lubrication, but our friendly professionals will show you the basics. We lubricate the hinges, rollers, bearing plates, center bearing, and springs. DAPco Garage Door Service Aledo utilizes a top-rated non-silicone based lubricate to apply on all the components in need of lubrication. Our tune up involves additional lubricating, inspecting the garage door opener, as well as the travel limits and travel force settings. On the garage door opener, we use a low temp grease based lubricant on the necessary elements, depending on the style and model of your garage door opener.

25 Point Garage Door Inspection

DAPco Garage Door Service Aledo 25 Point Inspection service on your Aledo areas home includes the following.

1. Door balance. This ensures the spring(s) are fully functionally.
2. Rollers. Our techs inspect every roller for signs of wear and tear, or damage.
3. Cables. Cables are inspected for fraying and kinking, which leads to damage.
4. Drums. Drum are looked over unusual defects and cracking.
5. Center Bearing. Inspection for wear and tear or burned out bearings is executed by United Garage Door. There are generally 2 types of center bearings; a single piece nylon bushing and a metal housing with actual ball bearings
6. Center Bracket. Center brackets are inspected for signs of bending and other anomalies.
7. End Bearing Plates. The bearing plates are located at each end of the spring bar mounted outside the drums. The bearings allow the spring bar to turn freely as the door opens and closes. We check to make sure there are no faults.
8. Spring Bar. We inspect for rust and bending. The spring bar holds the springs and turns as the door opens and closes.
9. Hinges. Hinges are inspected for damage and excessive wear.
10. Top Brackets. Top brackets hold the top roller in place, and most are adjustable to set the clearance between the jam and door.
11. Bottom Brackets. Bottom brackets are mounted at the bottom of the lower garage door
    Section, they hold the bottom rollers in place. These brackets contribute to the lifting point on the garage door. We inspected for wear, damage and breakage. WARNING! DO NOT REMOVE THE SCREWS FROM BOTTOM FIXTURES.
    CAN CAUSE SERIOUS INJURIES.\
12. Vertical Tracks. Bending and damage can occur; we check them to ensure they are up to par.
13. Horizontal Track. We also inspect for bending and damage.
14. Jamb Brackets. Jamb brackets attach the vertical tracks to the frame work on each side of the garage door opening, our Inspection searches for position, bending and other damage.
15. Strut. Struts are added supports for the garage door structure. Generally, garage doors have a strut mounted at the top of the high garage door section. Some garage doors are equipped with multiple struts depending on the weight of the door. Struts may be added if damage requires additional struts for support.
16. Weather Seal. Weather seals are rubber located at the bottom of the garage door. This seal helps prevent wind and windblown objects from entering the garage. We inspected for dry rot and any other damages.
17. Section (interior/exterior). We check for any dents, tearing in the metal along with any other damage.
18. Opener Controls. Controls are inspected for functioning efficiency.
19. Opener Trolley/Carriage. Inspected for damage and grinding in screw drive openers.
20. Safety Eyes. The safety eyes keep the door from closing if a person or object is in the garage doors path. Safety eyes are inspected for efficiency.
21. Motor Gears. Motor gears are susceptible to wear and tear in belt and chain drive we check the belt and/or chain for proper tension and sign of deterioration.
22. Wires. Visually inspected for any signs of wear and tear or cracking in the wire coating.
23. Limits. We test the limits to ensure the door opens and closes to the proper travel locations.
24. Opening/Closing Force: We also test the force limits to ensure there is proper force being applied to the door during opening and closing.
25. Springs. Finally, we visually inspect the springs for signs of rust and deterioration. We also measure each spring to make sure they are adequate.